Top 7 Costly Home Painting Exterior & Interior Mistake’s You Should Avoid

12 mins read
A house draining room

You want to paint your home a fresh color to make it look more modern. It looks to be rather easy. When you view all the newest TV remodeling programs, it seems effortless. Avoid being duped. Finding possible issues might be expensive, and it can be upsetting to say the least when anything goes wrong after all your hard work.

Problems with exterior paint and their solutions

Here is a list of exterior paint issues:

  1. Blistering paint
  2. Alligatoring and checking
  3. Efflorescence
  4. Mildew
  5. Running and Sagging
  6. Chalking
  7. Peeling

Exterior Paint Problems and Solutions

1.  Blistering Paint

What it is: Below the paint, there are small to medium-sized bubbles or blisters. Trim or wood siding are the most typical examples.

Causes: The paint was applied to a heated surface or in direct sunlight, causing the paint to dry too rapidly. Or the paint was applied to wet wood, and the water became trapped inside the paint. Similarly, dew, rain, or excessive humidity crept under the paint film after it dried.

Fix: Remove the blister using a flat scraping. Before proceeding, sand the area down to bare wood and allow it to dry fully. With high-quality latex paint, sand, prime, and paint in a dry environment away from direct sunlight.

2.  Alligatoring and Checking

What it is: An alligator-like skin-like pattern of cracking. With lengthy cracks, checking is a less severe version. It can create fractures and cracking in the paint if left unchecked.

Causes: Without waiting for the previous coat to dry completely before applying the next. With the first coat, the second did not adhere well. For instance, a latex paint cannot be applied over a glossy paint. By deteriorating with time, oil-based paints are susceptible to this.

Fix: You’ll need to start anew and totally remove the previous paint for this to be fixed. With flexible latex paint, sand, prime, and repaint the surface. The risk of this happening again decreases as quality increases.

3.  Efflorescence

What it is: Painted masonry has efflorescence. It appears like the paint is being penetrated by white, salty deposits.

Cause: The masonry or brick was improperly prepared before painting, which is one of the causes. From within the house, heavy dampness seeped through the stone walls. Before the mortar had fully dried, the bricks were painted. Because the basement walls were improperly waterproofed, ground water may seep in.

Fix: To begin with, you need to identify the source of the water that is harming your wall. To prevent this from happening again, patch and caulk the offending area. Wire brush any peeling or chalky paint, and eliminate any traces of efflorescence. Use a trisodium phosphate solution to scrub the area clean, then rinse well. Move only once it is entirely dry. Paint next with latex house paint.

4.  Mildew

What it is: Mildew is a fungus that consumes caulk or paint film. The typical appearance is a brown or green splotch.

Causes: Mildew develops because of moisture. It thrives in damp, dark, poorly ventilated environments. Mildew likes to develop on the underside of soffits and eaves. Mildew will continue to spread if it is painted over. A structure that is made of bare wood without priming is likewise ripe for mildew.

Fix: Use a solution of 1-part bleach to 3 parts water or trisodium phosphate cleanser to scrub the area. When handling chemicals, wear protective gloves and eyewear at all times. After around 15 minutes of drying time, rinse the area with fresh water. Give the surface enough time to cure before applying a premium latex exterior paint.

5.  Running or Sagging

What it is: Paint that is leaking or drooping may be the most typical exterior home painting issue.

Causes: Applying too much paint at once or thinning it excessively. The paint was either thicker due to the extreme cold or the excessive humidity. The area wasn’t cleaned before application or no primer was utilized.

Fix: To spread the paint more evenly if you notice this issue while you are still applying paint, use a brush or roller. Sand the area to make it even if the paint has already dried. Repaint. Avoid packing too much paint onto the brush, and apply two lighter layers as opposed to one thick one.

6. Chalking

What it is: Chalking appears as a powdery substance on top of external paint. Even while some chalking is common, it can nevertheless become an issue, particularly in dry environments. Chalking may indicate that the paint pigment is evaporating and the binders have degraded as a result of the weather. If the problem persists, the paint may start to flow off the home and taint the ground.

Causes: Low-cost paint containing a lot of pigment extenders external setting with inside paint. excessively thinned paint Prior to painting, porous areas were not sealed.

Fix: Use a trisodium phosphate cleanser to power wash or scrape the chalky region. Use clean water to rinse. Apply a premium latex house paint once it has dried. A specialist cleaning solution must be used if the area is made of masonry. If the issue persists, seek the advice of a cleaning.

7.  Peeling

What it is: This is a frequent problem brought on by moisture or inadequate adhesion. Paint is peeling off a prior layer as opposed to the substrate, which is the distinction.

Causes: The surface was either sparkling, dusty, or moist. Layers below did not stick together. Either the blistering wasn’t fixed or poor paint was applied.

Fix: Sand the problematic areas and scrape off the flaking paint. Spot prime the newly created empty space. Caulk as necessary, then repaint.

Interior Paint Problems and their Solutions

Here is a list of interior paint problems.

  1. Blistering
  2. Blocking
  3. Burnishing
  4. Cracking and Flacking

1. Blistering

What it is: As you paint, bubbles occasionally occur.

Causes of bubbling: It includes spreading alkyd or oil-based paint over wet or damp surfaces, losing adhesion, moisture that has gotten inside a house through external walls, and exposure of latex paint layer to moisture or high levels of humidity after the paint has dried.

Fix: If the blisters do not extend into the substrate, they may be eliminated by scraping, sanding, and repainting with high-quality acrylic latex interior paint.

2. Blocking

What it is: Blocking, which occurs when two painted surfaces adhere to one another, such as a door adhering to a jamb, is a common unexpected and unwanted outcome of interior painting.

Cause: Using inferior gloss or semi-gloss paints or failing to wait for painted surfaces to fully dry before closing windows and doors are a few of potential reasons.

Fix: Use high-quality gloss or semi-gloss acrylic latex interior paint and carefully adhere to the drying time recommendations in order to prevent blockage. Talc can be used to ease persistent blockage.

3. Burnishing

What it is: Paint burnishing is the process of rubbing paint against objects to raise the shine or gloss of the paint coat.

Cause:   The use of flat paint in high-traffic areas when a higher sheen level in the paint would be a better choice, frequent spot cleaning and washing, the use of low-grade paint with weak scrub resistance, and furniture or other objects rubbing against the walls are some of the potential causes of burnishing.

Fix: In high-traffic areas, use gloss or semi-gloss paint rather than flat sheen. Use high-quality latex paint on surfaces that need to be cleaned often, such doors and trim, as it has superior longevity.

4. Cracking and Flacking

What it is: The paint job may completely fail if the dried paint coat starts to break over time. This problem starts off as hairline cracks and progresses to flaking.

Cause: Interior paint cracking and flaking might be caused by overspreading or over-thinning the paint, using inferior paint that lacks flexibility and adhesion, improperly preparing the paint surface, employing inferior paint, or excessive alkyd paint hardening over time.

Fix: Sand the surfaces and edges that have a feathery look and remove peeling, loose paint with a wire brush or scraper. If many coats of paint are peeling, a filler may be necessary. Use a premium primer before re-painting exposed wood. Using a top quality paint to avoid the problem again.

Wrap Up

In this article, discover a variety of typical paint issues and how to fix them. We have mentioned that how to cure cracks, wrinkles, bubbles, and more from the interior to the exterior.

But It is advisable to engage a skilled professional paint contractor because the majority of paint issues are caused by ignorance of suitable procedures, preparation, and supplies. They have the knowledge and skills necessary to create a paint job of the highest caliber that will last for many years.

Leave a Reply

Your email address will not be published.